Motors and Wheels Archives - Supreme Light Technology

Showing all 38 results

1.8V – 12V/2A DC Motor PWM Speed Regulator

Input supply voltage: 1.8V- 15V DC.
The maximum output power: 30W
Output current : 2A(Max).
With resettable fuse.
Equipped with LED indicator.
Potentiometer with switch function for PWM adjustment.

16 Channel PCA9685 12-bit PWM Servo Shield Motor Driver I2C

6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
Adjustable frequency PWM up to about 1.6 KHz
12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
Configurable push-pull or open-drain output
Output enable pin to quickly disable all the outputs

2 Axis Servo Pan Tilt Platform for Camera/Sensor

PV Nylon Head Two Axial plastic
Two axial platform
Anti-vibration
lightweight
Good design and shape
Sophisticated products
Provision to add standard servo motors (sold separately)
Pan and tilt using simple PPM interface using RC servos with position control.
180 Degree of freedom on both axis.
Supported Motors: SG90, Mg90s

30A Brushed ESC with Brake Electronic Speed Controller

Support forward, backward, with the brake switch.
Be suitable for 130/180/260/280/380 brush motors, 1/16 1/18 1/24 RC car/ boat/ tank.
Replacement for HSP Redcat Traxxas Tamiya HPI rc4wd axial RC cars.
Voltage support: 4~8V.
Forward 30A
Instantaneous peak value 40A
Backward 20A
UBEC output: voltage 5.7V, current 1A.

4.8-6V Servo Motor Tester with Indicator Light

Supply voltage: 4.8V-6.0V
Output Signal: 1.5ms±0.5ms
Three mode selection [Manual, Neutral and Auto]
Enclosure Box
Mode selection LED Indicator
Adjustable Knob for manual speed control
Operating Temperature Range: -40~+85°C

43mm Rubber Wheel Tyre for N20 Mini Metal Gear Motor

Coder Accuracy: 12 pulses per revolution
Heavy Duty Material
Durable and specially design 3PI miniQ Car wheel

A4988 Stepper Motor Driver Module CNC Shield Compatible

Max. Operating Voltage: 35V
Min. Operating Voltage: 8V
Max. Current Per Phase: 2A
Microstep resolution: Full step, ½ step, ¼ step, 1/8 and 1/16 step
Reverse voltage protection: No
Dimensions: 15.5 × 20.5 mm (0.6″ × 0.8″)
Short-to-ground and shorted-load protection
Low RDS(ON) outputs
Thermal shutdown circuitry

Arduino CNC Shield for Stepper Motor

Arduino UNO shield form factor, compatible with Arduino UNO.
GRBL v1.1 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
Uses removable A4988 compatible stepper drivers (Not Included)
PWM Spindle and direction pins
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins A4 and A3)
2 x End stops for each axis (6 in total) + one Probe
Coolant enable output
Jumpers to set the Micro-Stepping for the stepper drivers.
Stepper Motors can be connected with 4 pin connectors or soldered in place.
Runs on 12-35V DC. (Depending on Stepper driver

Hot

BO Wheel 65mm Diameter 26mm Width Yellow

Shaft Diameter (mm) : 5.4mm-(round side) and 3.5mm-(flat side)
Wheel Diameter(mm) : 65
Wheel Width(mm) : 26
Loading Capacity (Kg) : 2

Hot

BTS7960 Motor Driver Module 43A H-Bridge High-Power

Double BTS7960 large current (43 A) H bridge driver
5V isolate with MCU, and effectively protect MCU
5V power indicator on board
voltage indication of motor driver output end
can solder heat sink
Overvoltage lock up
Undervoltage shut-down
Overtemperature protection
Current limitation
Short-circuit protection
Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2)
isolation chip 5 V power supply (can share with MCU 5 V)
Able to reverse the motor forward, two PWM input frequency up to 25kHZ
two heat flow passing through an error signal output
isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply
the supply voltage 5.5V to 27V

DC Gear Motor for DIY Robotic Car - 10 RPM

Operating Voltage(V): 12
Rated Torque(kg-cm): 7
Stall Torque(kg-cm): 28

DC Gear Motor for DIY Robotic Car - 1000 RPM

Operating Voltage(V): 12
Rated Torque(kg-cm): 2
Stall Torque(kg-cm): 15

DC Gear Motor for DIY Robotic Car - 300 RPM

Operating Voltage(V): 12
Rated Torque(kg-cm): 4
Stall Torque(kg-cm): 15

DC Gear Motor for DIY Robotic Car - 45 RPM

Operating Voltage(V): 12
Rated Torque(kg-cm): 6
Stall Torque(kg-cm): 25

DC Gear Motor for DIY Robotic Car - 500 RPM

Operating Voltage(V): 12
Rated Torque(kg-cm): 3
Stall Torque(kg-cm): 15

DC Gear Motor for DIY Robotic Car - 60 RPM

Operating Voltage(V): 12
Rated Torque(kg-cm): 5
Stall Torque(kg-cm): 15

DC Worm Geared Motor High Torque 100 RPM 12V

Voltage: DC12V
Load torque: 10KG.CM
RPM: 100

DC Worm Geared Motor High Torque 200 RPM 12V

Voltage: DC12V
Load torque: 10KG.CM
RPM: 200

Double Metal Shaft BO Motor for RC Car

Operating Voltage (VDC):3 ~ 6
No Load Current (mA):40-180mA.
Type: Brushed
Shaft :
- Type: Dual D
- Length (mm):8.7 & 9.3
- Diameter (mm):5.5
Gear:
- Material: Metal
- Ratio:1:90
Rated Speed After Reduction (RPM):110
Rated Torque (Kg-Cm):1

Hot

Double Shaft BO Motor for RC Car

Working voltage : 3V to 9V
30gm weight
Ability to operate with minimum or no lubrication, due to inherent lubricity.
1.9Kgf.cm torque
No-load current = 60mA, Stall current = 700mA

High Torque Side Shaft DC Gear Motor 12v With Encoder

Operating Voltage: DC 12V
Shaft Diameter: Approx. 6mm / 0.2in (D Shaft)
Shaft Length: Approx. 15.5mm / 0.6in
Current: 0.45A/1A
Speed: 6~1590 RPM
Maximum torque: 2KG.CM
Output shaft: 21.5mm

Hot

Hobbywing QuicRun 1060 60A Brushed ESC Waterproof

Waterproof
Cont./Peak Current – 60A/360A
Input – 2-3S LiPo/6-9 Cells NiMH
BEC Output – Switch Mode:6V/3A
Motor Limit – 2S Lipo or 6 NiMH – 540 or 550 Size Motor: 12T or RPM 30000 – 7.2V
3S Lipo or 9 NiMH – 540 or 550 Size Motor: 18T or RPM 20000 – 7.2V
Input Wires – Red-16AWG-100mm/Black-16AWG-100mm
Output Wires – Blue-16AWG-100mm/Yellow-16AWG-100mm
Input Connectors – Big-sized TAMIYA Connector
Output Connectors – 4.0 Bullet Connectors (Female)

Johnson Gear Motor 200 RPM 12v for robotics

Rpm - 200 shaft
Diameter - 6mm (with internal hole)
Gearbox diameter: 37mm
Motor diameter: 28. 5 mm
Voltage: 6 to 24 (nominal voltage - 12v)

Johnson Gear Motor 300 RPM 12v for robotics

Rpm - 300 shaft
Diameter - 6mm (with internal hole)
Gearbox diameter: 37mm
Motor diameter: 28. 5 mm
Voltage: 6 to 24 (nominal voltage - 12v)

Johnson Gear Motor 500 RPM 12v for robotics

Rpm - 500 shaft
Diameter - 6mm (with internal hole)
Gearbox diameter: 37mm
Motor diameter: 28. 5 mm
Voltage: 6 to 24 (nominal voltage - 12v)

Hot

L293D Arduino Motor Driver Shield

L293D is a monolithic integrated, high voltage, high current, 4-channel driver.
Can drive 4 DC motors or 2 stepper motors or 2 Servo.
Up to 4 bi-directional DC motors with individual 8-bit speed selection.
Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 10V DC.
Pull down resistors keep motors disabled during power-up.
reset button.